[MODE]+PAD6


Press the F3[Zoom In] key, a waveform is zoom in.
BAR > or [SHIFT]+ cursor key can also perform zoom in.
A level is expanded and displayed by cursor key.


Press the F2[Zoom Out] key, a waveform is zoom out.
< BAR or [SHIFT]+ cursor key can also perform zoom out.
Note: Cursor move on a sample name should press the cursor key, when cursor is in St field.

Adjustment of a start point

Please move cursor to the St field and turn a DATA wheel.
(A value can be changed 10 times by a [SHIFT]+DATA wheel.)
Furthermore, it can be changed by Q1Slider, if Q1[AFTER] key is ON.

Adjustment of an end point

Please move cursor to the End field and turn a DATA wheel.
(A value can be changed 10 times by a [SHIFT]+DATA wheel.)
Furthermore, it can be changed by Q2Slider, if Q2[AFTER] key is ON.
Note: A start or an end point can be adjusted auditioning, if a DATA wheel is turned pressing arbitrary pads.


When cursor is a Sample field, press the [WINDOW] key, the "Sample list" window will open.


Chooses a sample by a DATA wheel or cursor key, pressing a arbitrary pad, audition is Possible.

INSERT SILENCE, STEREO =>MONO, BIT CONVERT, and RING MODULATION were added to F6[EDIT].

F6[EDIT]

DISCARD
EXTRACT
DELETE
SILENCE
INSERT SILENCE
NORMALIZE
REVERES
TIME STRETCH
PITCH SHIFT
STEREO L=> MONO
STEREO R => MONO
STEREO L+R => MONO
STEREO L-R => MONO
BIT CONVERT
RING MODULATION

INSERT SILENCE

The silence of the set time is inserted from a start point.
In the case of the above figure, the silence of 100mSEC is inserted from the start point set in TRIM mode.

BIT CONVERT

A sample can be converting into the sound of 4-12 bits.
F2(OVER W) = An overwrite convert is carried out with the set value.
F3(ALL) = The overwrite convert of all the samples is carried out with the set value.
If PAD13-PAD16 is pressed, the audition of the present set point can be performed.
If PAD01-PAD12 is pressed, it can try listening an original sound.
Note: File size does not change after convert.

RING MODULATION

The output of two oscillators is mixed and a metallic sound is made.
An audition is possible, when F2[PLAY] key or PAD13-PAD16 is pressing.
Frequency: 100Hz-5000Hz
WAVE:Sine,Square
Mix : 1-10

CHOP


Press F5[CHOP] key.


When cursor is in St field, the start point of a region can be adjusted.
When cursor is in St field, if the cursor key is pressed, the cursor in the region field will move to a left region.


Please move cursor to the End field to adjust the end point of a region.
When cursor is in End field, if the cursor key is pressed, the cursor in the region field will move to a right region.
A level is expanded and displayed by or cursor key.
BAR > or [SHIFT] + cursor key can also perform zoom in.
< BAR or [SHIFT] + cursor key can also perform zoom out.
Move of a region can be performed even if it turns a DATA wheel, pressing or cursor key.

AUTO

Press F2[AUTO]


If AUTO is used, search of an attack will be performed automatically and it will be divided on the basis of the attack portion.
Recovery time(10 - 100): This sets the minimum time between the attack and the next attack. (The attack within a time is ignore.)
Threshold(0 - 100): This sets the detectable level of an attack.
If a setup finishes, please press the F5[DO IT] key.


Note: The sample for 20 seconds or more cannot AUTO.

SLICE

If the F3[SLICE] key is pressed, it becomes slice mode and the number of regions can be changed. (2-64)
Slice mode will be canceled, if the F3[SLICE] key is pressed once again or the cursor key is pressed.

DIVIDE

The region chosen by press the F4[DIVIDE] key is divided into two.



COMBINE

The region chosen and an adjoining region are combined by press the F5[COMBINE] key.


When cursor is in St field, it combines with the region by the side of a start (left), and when it is in the End field,
it combines with the region by the side of End (right).

EDIT

If the F6[EDIT] key is pressed, the window of "Extract" will open.


F5[DO IT]: The selected region is made into another sample.
F2: Each which was divided on a slice point is made into another sample.
For example, in the case of Sample01 divided into 32, the samples from Sample01-1 to Sample01-32 are created.
F3: It changes into a Patched Phrase.
Note: It becomes a mono sample when the sample of a stereo is changed into Patched Phrase.

Setting the loop


Please press the F1[LOOP ON/OFF] key and make it [LOOP ON].

Adjustment of a loop point

Please move cursor to the Loop field and turn a DATA wheel.
(A value can be changed 10 times by a [SHIFT]+DATA wheel.)
Furthermore, it can be changed by Q1Slider, if Q1[AFTER] key is ON.

Adjustment of a end point

Please move cursor to the End field and turn a DATA wheel.
(A value can be changed 10 times by a [SHIFT]+DATA wheel.)
Furthermore, it can be changed by Q2Slider, if Q2[AFTER] key is ON.


If the F4(JOINT) key is pressed, the window of "Joint" will open.


It can adjust looking at a joint.
The screen left is an end point and the right is a loop point.
A level is expanded and displayed by cursor key.

Selection of loop mode


Please move cursor to the loop mode field, and turn and select a DATA wheel.
= Forward loop. (From a loop point to between end points, playback is repeated to a forward direction.)
= Alternate loop. (From a loop point to between end points, playback is repeated for a forward direction/reverse direction alternately.)

Linking the loop point to the start point


Please move cursor to field.
Turn the DATA wheel and set the field to(locked by the key).


A loop point becomes the same value as a start point, and a start point will also be changed into the same value if a loop point is changed.
A loop point will also be changed into the same value if a start point is changed similarly.
Please restore to(unlocked by the key) to set up a loop point and a start point separately.

---How to reduce the loop noise of a sample---