[MODE]+PAD6
Please adjust a start point and an end point if needed.
And please press F6 (EDIT) button and select an edit function.

A play marker will be displayed if the audition of the sample for 1 seconds or more is carried out. (A play marker is not displayed when zoom of the waveform is carried out.)
If < <BAR>> button is pressed, waveform zoom-in/out will be performed.
A gain will be expanded and displayed if [SHIFT] + or cursor button is pressed.

Adjustment of a start point
Please move cursor to the St field and turn a DATA wheel.
If a DATA wheel is turned holding [TAP TEMPO] or the [SHIFT] button, the quantity of change will increase 10 times.
If Q1 [AFTER] button is ON (the LED is lit), start point can be adjusted with a Q1 slider.

Adjustment of a end point
Please move cursor to the End field and turn a DATA wheel.
If a DATA wheel is turned holding [TAP TEMPO] or the [SHIFT] button, the quantity of change will increase 10 times.
If Q2 [AFTER] button is ON (the LED is lit), end point can be adjusted with a Q2 slider.

If PAD9-PAD12 is pressed, a sample will be played back as shown in the following figure.
Moreover, the range will blink only once.



If PAD1-PAD4 is pressed, a sample will be playback by NOTE ON.
If PAD5-PAD8 is pressed, a sample will be playback by ONE SHOT.
A sample will be reverse-played back if PAD3 and PAD7 are pressed.
Moreover, a start point or an end point can be adjusted, carrying out audition, if a DATA wheel is turned pressing a PAD1-PAD4.
The range which will be played back if PAD14-PAD16 are pressed will blink only once.

F6 (EDIT) Edit function.
DISCARD
EXTRACT
DELETE
NORMLIZE
SILENCE
INSERT SILENCE
REVERSE
BIT CONVERT
FADE IN
FADE OUT
COMBINE
MIX
TIME STRETCH
PITCH SHIFT
RING MODULATION
STEREO L=>MONO
STEREO R=>MONO
STEREO L+R=>MONO
STEREO L-R=>MONO
STEREO LR CHANGE
INVERT

INSERT SILENCE


The silence of the set time is inserted from a start point.
In the case of the above figure, the silence of 100mSEC is inserted from the start point.

BIT CONVERT


A sample can be converting into the sound of 4-12 bits.
If F1(PLAY) button is pressed, the audition of the present set value can be performed.
If F2 (OVER W) button is pressed, an overwrite conversion will be carried out with the set value.
If F3 (ALL) button is pressed, the overwrite conversion of all the samples will be carried out with a set value.

Note: File size does not change after convert.

COMBINE


Two samples are combined.
When a noise is in joint, please set the "Fade A>Out-B<In" field to ON.

Note: When TUNE is set to the sample, it is set up with the value of Sample A.

MIX


Two samples are mixed.
Please adjust LEVEL if needed.
If F2 (PLAY) button is pressed, the audition of the mixed sample can be performed.
The sample to which TUNE is set sounds by TUNE 00:00.
The sample of ON of a loop sounds by Loop OFF.

Notes
The sample to which TUNE is set is mixed as TUNE 00:00.
The sample of ON of a loop is mixed as OFF.
A Patched Phrase sample is unmixable.

RING MODULATION


The output of 2 oscillators is mixed and a metallic sound is made.
If F2 (PLAY) button is pressed, the audition of the present set value can be performed.

Frequency:	100Hz-5000Hz
WAVE :	Sine,Square.
Mix:	1-10 The ratio to an original sound is set. An original sound becomes 90% when 1 is set. The sound for which the effect was adapted becomes 10%. When 10 is set, it becomes only the sound for which the effect was adapted.

INVERT


A waveform is inverted.

Next page